Model C98
Motion Detecting Door Control Panel
OWNERS INSTRUCTIONS
WARNING
DO NOT CONNECT TO LIVE ELECTRICAL WIRING. CONNECT
ONLY TO 24 VOLT LOW VOLTAGE WIRES. CONNECTION TO
LIVE WIRES OR HIGHER VOLTAGE MAY CAUSE SERIOUS
INJURY FROM SHOCK, BURN OR ELECTROCUTION.
Children operating or playing with a garage door opener can injure
themselves or others. The garage door could close and cause serious
injury or death.
Install the door control (or any additional push buttons) out of the
reach of children and away from all moving parts of the door and door
hardware, but where the garage door is visible. Do not allow children
to operate the push button(s) or the remote control transmitter(s).
A moving garage door could injure someone under it. Activate the
opener only when the door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
LOCK
LIGHT
To Replace
Insert Top
Tabs First
STANDARD WALL MOUNT
Detector
Switch
Push Bar Cover
ON
OFF
LOCK
LIGHT
Push Bar
Light Button
Lock
Button
LOCK
LIGHT
1
RED
2
WHITE
Door
Control
Terminal
Screws
2-Conductor
Bell Wire
professional
5
0
50
180 sec.
red
white
MR800a/MR600a
6mm
1
2
1
3
2
60 s
180 s
O
–
6mm
red
white
1
2
red white
red
white
This door control contains a motion
detector which automatically turn your openers
light on when it detects a person entering the
garage. This feature may be disabled if
required.
Locate the door control within sight of the
door at a height of no less than 1.5m out of
the reach of children and away from any of
the door’s moving parts and hardware.
INSTALLATION
The door control is typically attached directly to the wall.
However you may use a single gang wall box if installed.
Note: If installing close to door frames or other switching
devices ensure the detector switch (right side of unit) is
accessable.
• Disconnect power to the garage door opener.
• Strip wire insulation approx 6mm and connect
wire with Red trace to the “R” terminal, connect
white non trace wire to the “W” terminal.
• Remove the push bar by gently
prying off the top edge with a
flat blade screwdriver or coin.
• For standard wall mounting,
mark a position on the wall
approximately 20mm above
the desired mounting height of
no less then 1520mm. Partially
fasten the self tapping screw into the wall
leaving around 5mm of thread protruding from
the wall. Slip the lower part of the cover over
screw head and adjust for a snug fit.
Ensure the Wall control is level, then fasten
the top screw through the hole located at the top
of the wall controller. DO NOT OVERTIGHTEN.
Run the cable provided up the wall and across
the ceiling to the open, using the insulated staples
or surface mount conduit (not provided) to secure
cable into place. Take care not to to damage cable.
MR800a /
MR600a
MT60
MT600 /
MT1000
MT5580
Motor Connetions
Ensure the power to the unit is off.
MT60: Open the light cover at the front of the motor.
direct the bell wire throught the rectangular opening
located above the unit’s terminals.
Connect the Red/White wire to the 1 terminal then
connect the White wire to the 2 terminal.
MT600/1000: Connect the Red/White wire to the
Red number 1 terminal located on the back of the unit.
MR600a/800a: Gently lift the light diffuser up and away
from the motor.
Connect the Red/White wire to the Red terminal located
on the unit’s control board then connect the White wire
to the White terminal.
MT5580: Connect the Red/White wire to Red terminal
located on the back of the unit then connect the White
wire to the White terminal.
red
white
partially
fastened
screw
(68 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals